Skip to main content invisibro (u/invisibro) - Reddit
invisibro u/invisibro avatar

invisibro

u/invisibro

Feed options
Hot
New
Top
View
Card
Compact






They don't know what's causing the failures. So many reports of multiple CPUs fried. I had one fried on bios 3.40 before I switched to gigabyte.

If any diehard ASRock fan who thinks we're still making these failures up wants to buy an x870e nova wifi, I have one that was only used 3 weeks!





Update: AMD RMA completed and received a replacement 9800X3D. While the RMA was processing, I swapped in a Gigabyte X870 Aorus Elite motherboard. Threw in the processor today and am back up and running.




You keep posting this but I haven't found a single case in this subreddit searching for "discharge" where someone has replied that this has worked for a CPU error - only Bluetooth issues or other components.







It ran fine for almost a whole month - I played the entirety of Phantom Liberty and most of Silksong. Then I tried to boot it this morning and got error code 00.

The first thing I did was reset CMOS, take the CPU out and examine the CPU and socket pins (no visible issues), reinstall the CPU and cooler and try to boot again, and got the same error code.









Sekiro does everything way, way better than silksong in its current state. Spirit emblems have no max (they get banked in your inventory), you can buy them at any rest point and enemies drop plenty of money.. And bosses don't spawn minions to make the fights RNG.


Itll depend on a variety of factors: dose, basket, grinder, beans, bottom paper filter or no, etc.

General starting point for any manual machine (flair, robot, oxo rapid brewer, etc) is to grind to where you see drips when you add water but still have to apply a little pressure to get the puck gently soaked and the puck screen filled. Then you ramp up flow to finish the shot. Whole shot should not exceed 1 bar.

Then adjust grind to taste on subsequent shots. Sour/weak grind finer. Bitter/harsh grind coarser.

















[USA - TX Austin] [H] Bunnzilla G1 with 80mm Ditting 804 Burrs - $650 - Venmo, Zelle, Cash
[USA - TX Austin] [H] Bunnzilla G1 with 80mm Ditting 804 Burrs - $650 - Venmo, Zelle, Cash

Edit: SOLD

Have a Monolith Max arriving Monday, so I'm putting my faithful Bunnzilla up for sale. This has by far been the best coffee investment I've made in producing quality brewed coffee. With this grinder, if the coffee doesn't turn out tasty, you know it's the beans.

Details:

  • Bunn G1 with 80mm Ditting 804 machined steel burrs with Mill City Roasters conversion ring

  • Trifecta plate installed with 27 fineness steps

  • Single dose grinds in about a second (can grind 1lb of beans in 30 seconds)

  • Built in Oct 2016

  • Dimensions: 7.3 in. W x 16 in. D x 22.8 in. H

  • Roughly 200lb ground so you don't have to break in the burrs (the burr life expectancy according to Ditting is ~15,000 pounds)

  • Performed sandpaper burr alignment which improved consistency of drawdowns (even at finer settings) & sweetness in the cup

  • Only minor issue is that the off switch does not work (probably easily fixed with a switch replacement), but the grinder does turn off automatically when the safety lever behind the chute is no longer depressed. Remove your catch cup/bag/etc and the grinder turns off.

  • Local pickup preferred (Austin, TX), but could look into shipping - I expect shipping cost would be pretty pricy since the G1 weighs about 50 pounds

  • Prefer to sell as-is, but willing to sell burrs & grinder separately if there is no interest in the full grinder




Same issue. Had mine limited to 159fps before which i consistently maxed out on smaller maps. Struggling to get 114 now, and it doesn't actually feel like 114 - it's choppy as hell.

Even the character animation on the Multiplayer screen stutters