Electronics World articles Popular Electronics articles QST articles Radio & TV News articles Radio-Craft articles Radio-Electronics articles Short Wave Craft articles Wireless World articles Google Search of RF Cafe website Sitemap Electronics Equations Mathematics Equations Equations physics Manufacturers & distributors LinkedIn Crosswords Engineering Humor Kirt's Cogitations RF Engineering Quizzes Notable Quotes Calculators Education Engineering Magazine Articles Engineering software RF Cafe Archives Magazine Sponsor RF Cafe Sponsor Links Saturday Evening Post NEETS EW Radar Handbook Microwave Museum About RF Cafe Aegis Power Systems Alliance Test Equipment Centric RF Empower RF ISOTEC Reactel RF Connector Technology San Francisco Circuits Anritsu Amplifier Solutions Anatech Electronics Axiom Test Equipment Berkeley Nucleonics Conduct RF Copper Mountain Technologies everything RF Exodus Advanced Communications Innovative Power Products KR Filters LadyBug Technologies PCB Directory Rigol Temwell RF Components TotalTemp Technologies Werbel Microwave Windfreak Technologies Wireless Telecom Group Withwave Sponsorship Rates RF Cafe Software Resources Vintage Magazines RF Cafe Software WhoIs entry for RF Cafe.com Thank you for visiting RF Cafe!
Axiom Test Equipment - RF Cafe

Temwell (RF components)

Exodus Advanced Communications Best in Class RF Amplifier SSPAs

Please Support RF Cafe by purchasing my  ridiculously low−priced products, all of which I created.

RF Cascade Workbook for Excel

RF & Electronics Symbols for Visio

RF & Electronics Symbols for Office

RF & Electronics Stencils for Visio

RF Workbench  (shareware)

T-Shirts, Mugs, Cups, Ball Caps, Mouse Pads

These Are Available for Free

Espresso Engineering Workbookâ„¢

Smith Chartâ„¢ for Excel

Anritsu Test Equipment - RF Cafe

Understanding Super-Modulation
February 1950 Radio & Television News

February 1950 Radio & TV News
February 1950 Radio & Television News Cover - RF Cafe[Table of Contents]

Wax nostalgic about and learn from the history of early electronics. See articles from Radio & Television News, published 1919-1959. All copyrights hereby acknowledged.

A few weeks ago I posted a two-part article on the Taylor super-modulation principle published in Radio & Television News magazine in 1948. It was a newly announced technology at the time and was written by its inventor, Robert Taylor. This piece entitled "Understanding Super-Modulation" appeared a couple years later by another author, John McCord, where he describes how it works , how to tune super-modulation circuits, and how it compares to other modulation methods - all conveniently in "Ham language." Super-modulation is a form of amplitude modulation (AM) that makes use of carrier and/or sideband suppression to achieve greater efficiency. A panadaptor - aka pan-adapter, aka panadapter, aka radio spectrum scope, aka panoramic adapter - is used to view the RF spectrum across a wide band. Essentially it is a low budget spectrum analyzer.

Panadapters are now available as add-on features of software defined radios (SDR).

See also "The Taylor 'Super-Modulation' Principle" Part 1 (Sep. 1948), Part 2 (Oct. 1948), "Understanding Super-Modulation" (Feb. 1950)

How it works, tuning instructions, and a comparison with other modulation methods, as seen on a Panadaptor.

Super-modulated amateur station - RF Cafe

Super-modulated amateur station designed and built by W1BIJ. (Left to right) Super-modulated final amplifier using 807's, the v.f.o. and driver, 15-tube superhet for ham bands, and the 12-tube Panadaptor used in the signal comparison tests at the station.

By John K. McCord, W1BIJ

A new method of amplitude modulation has appeared recently. It is simple and efficient and readily adapted to amateur use. In building a low-power transmitter using the "super-modulation"* principles and getting it on the air, several major differences, compared to regular AM methods, were noticed. This article will explain in practical "ham" language what happens in a super-modulated rig that makes it so different from conventional AM transmitters. A step-by-step tuning method and panoramic comparison with other systems will also be covered. Fig. 2 is the home station final using 807 tubes in super-modulation.

For a basic understanding of super-modulation operation see Fig. 1. The unfamiliar tank circuit is electrically the same but redrawn to simplify an understanding of the action. The r.f. tube functions as a regular class "C" amplifier. The p.m. or r.f. modulator tube, being biased about four times cut-off, doesn't go to work until you speak into the microphone to modulate. The r.f. tube makes the carrier and the p.m. tube puts your voice on it by adding r.f. power to the common tank at an audio rate.

RF tube plate is shunt-led and the p.m. plate series-led - RF Cafe

Fig. 1 - The r.f. tube plate is shunt-led and the p.m. plate series-led to allow use of separate plate current meters. For a diagram of complete unit and an identification of parts see the schematic shown in Fig. 2.

Circuit diagram and parts list for the super-modulation final amplifier - RF Cafe

Fig. 2 - Circuit diagram and parts list for the super-modulation final amplifier and modulator.

RF tube drive should be adjusted to prevent carrier clipping - RF Cafe

Fig. 3 -  How r.f. tube drive should be adjusted to prevent carrier clipping yet retain high modulation peaks. (A) Carrier only. (B) overmodulation with clipping. (C) under 100% modulation.

Graph showing the super-modulated output waveform and its - RF Cafe

Fig. 4 - Graph showing the super-modulated output waveform and its separate components, drawn on a common time base.

Panadaptor image showing method for determining relative carrier strength - RF Cafe

Fig. 5 - Panadaptor image showing method for determining relative carrier strength, per-cent modulation, and bandwidth. Point "A" is 10 kc. marker. "B" voice peak. "C" carrier level. "D" bandwidth, and "E" carrier clipped showing overmodulation. This signal is overmodulated as shown by flattening at "E."

Same signal 100% modulated, as seen on Panadaptor screen - RF Cafe

Fig. 6 - (A) Unmodulated regular method AM carrier only. (B) Same signal 100% modulated, as seen on Panadaptor screen.

Carrier only super-modulated signal - RF Cafe

Fig. 7 - (A) Carrier only super-modulated signal. (B) Fully modulated "super" as seen on Panadaptor. Notice extended positive peaks and suppressed carrier (lower peak).

NBFM signal without modulation - RF Cafe

Fig. 8 - (A) NBFM signal without modulation. (B) Same signal modulated ±3 kc. Notice dead spot at "C."

Fig. 4 shows the super-modulation output waveform and its separate components drawn on a common time base. As the p.m. tube's fixed grid bias is series-fed through the modulation transformer secondary, and the r.f. tube bias is in shunt to the transformer center tap (see Fig. 2), the first audio voltage cycle from the modulation transformer secondary being a.c., alternately adds and subtracts from the fixed bias supply voltage. As a result both the r.f. and p.m. tube outputs increase and decrease accordingly. At time instant "A" in Fig. 4, an unmodulated carrier from the r.f. tube is shown. At "B," the start of the first positive audio alternation increases the r.f. carrier slightly to provide a cushion for the coming p.m. tube operation. At "C" the full peak of the positive audio alternation has cancelled out the p.m. tube's fixed bias and driven the grid positive resulting in a very large amount of power released. At this point the p.m. tube demands maximum r.f. grid drive. By preference less drive is left for the r.f. tube grid and its output drops, suppressing the carrier. At "D" the p.m. tube's power cycle is ending and the r.f. tube's carrier rises as a result of returned grid r.f. drive and provides the final cushioning. At "E" the negative audio alternation adds to the p.m. tube's fixed bias and the p.m. grid is momentarily about eight times cut-off. Through the modulation transformer center tap this same negative voltage adds to the r.f. tube's fixed bias and decreases its output, forming the negative or valley portion of the output waveform. This completes one cycle of audio voltage from the modulator and this is repeated for each succeeding cycle. This method of AM modulation has the following advantages. The positive waveform peaks can be extended to a point only limited by the p.m. tube's plate saturation point and the r.f. carrier can be suppressed at the same time. Using regular AM methods, extending the positive peaks beyond the 1000/0 modulation level would result in a clipped carrier. With super-modulation the r.f. tube supplies some carrier at all times and fills in between modulation peaks, preventing carrier clipping regardless of how high we extend the positive peaks, and it's the peaks that carry the voice intelligence.

Regarding power supply requirements, two plate supplies are not needed. The r.f. and p.m. tubes do not draw maximum plate current at the same time, so any supply adequate for a single tube will be OK. Grid bias can be supplied either by batteries or a separate supply. I tap mine off of the driver power supply bleeder. The r.f. tube can operate with grid-leak bias, but the p.m. tube must have a fixed supply and a means of varying the bias voltage over a small range. Tuning the super-modulated transmitter is quite different from usual procedure and the method is given step-by-step below. It is assumed bugs and parasitics have been eliminated from your super-modulated final and enough r.f. drive is available for a single tube. Both finals do not require maximum drive at the same time. Start with final plate voltage off.

1. Vary the r.f. grid drive and grid bias voltage until the r.f. tube grid draws 1/2 normal drive and the p.m. grid is zero or just starting to draw current. This balance is important. Run the r.f. tube cool and let the p.m. tube do the work.

2. Closely couple a dummy antenna to the final tank and switch on plate voltage. The r.f. tube should load normally like a c.w. rig with the key down. Reduce grid drive rather than antenna coupling to decrease loading. The amount of coupling affects the tank impedance into which the p.m. tube works.

Keep the r.f. tube running cool at about half c.w. rating, but enough to prevent carrier clipping during modulation. An oscilloscope check will show the right point.

3. Now apply modulation while increasing the audio gain. The p.m. tube grid and plate current should both kick upward to high values. The r.f. tube grid and plate current should show a downward movement, indicating carrier suppression. My 807 p.m. tube shows plate current peaks of 80 to 100 ma. and over. As the meter indicates an average value, the true peak current is about twice that shown.

4. Disconnect the dummy antenna and load the regular antenna to approximately the same tuning values.

The oscilloscope pattern of Fig. 3 shows how the r.f. tube drive should be adjusted to prevent carrier clipping and still retain high modulation peaks. The vertical scope plates were directly link-coupled to the final tank which was loaded with the dummy antenna. Warning - If scope is left coupled to tank when using antenna, r.f. may be fed to the power lines or the connecting leads may radiate, causing TVI, etc., so check this point carefully.

Checks have been made using a 5-inch Panadaptor to compare super-modulation waveforms with other signals on the air. The human ear is quite unreliable, even though we all use it for this purpose. Being logarithmic in function and having poor retaining qualities we shelved it along with the average receiver "S" meter and found the Panadaptor to be a decided improvement. Using this visual method small changes in both carrier and modulation could be seen. A change in amount of modulation not noticed by the ear can make a real difference in signal-to-noise ratio at a distant receiving location. It can mean the difference between being readable and not readable. The Panadaptor shows this difference. Fig. 5 is a mock-up waveform showing method used to determine relative signal characteristics with the panoramic image.

An average regular-method AM signal on the air appears as shown in Fig. 6. Notice that the modulation peaks extend just to twice the carrier height without modulation, and recede to the zero base line. This represents 100% modulation. Extending the peaks higher would also make the bottom peaks go lower which they can't do without hitting the zero base line and clipping the carrier. Fig. 7 shows a super-modulated signal of about the same power or pip height. Notice the positive peaks extended to three times the unmodulated carrier level, yet the carrier is a long way from being clipped. The carrier has even been suppressed to minimize heterodyne tendencies with other carriers. This is still amplitude modulation, but with greatly extended positive peaks. Fig. 8 is an average. NBFM signal with narrow deviation, and no splatter when received on an AM receiver. The amount of voice power is small and even using a discriminator for correct reception results in low audio content because of the small deviation allowable.. Wideband commercial FM stations, of course, are very efficient. NBFM has many advantages, but voice efficiency is low. It is evident that super-modulation delivers far more "talk-power," as Mr. Taylor calls it, than any of the other types of signals shown. Perhaps some day we may report a received signal as: "Fine business OM or coming in 10 db. over 9 on my Panadaptor. Your modulation is about 80% and your bandwidth is 8 kc." This report would give the operator real information.

While operating a super-modulated transmitter some major differences were noted compared to the operation of a conventional plate-modulated AM rig.

1. Using regular AM methods the final r.f. plate meter should not vary with modulation. With super-modulation it should, and does, vary. In fact, they vary, both the r.f. and p.m. tube plate milliammeters. If they don't, you are not modulating.

2. When receiving a regular method AM signal the "S" meter indicates carrier strength. A strong movement of the needle with modulation could indicate overrnodulation. With super-modulation a large needle movement is normal, indicating extended positive signal peaks. On one transmission check with super-modulation the "S" meter read S-9 with the carrier only and reached 15 db. over on peaks. "S" meters are relative indicators only and should not be depended upon for ac-curate measurements.

3. In modulating the usual plate-modulated AM transmitter, an audio power equal to 50% of the r.f. final stage power is required of the modulator. With super-modulation the modulating power is r.f., not audio, and is supplied by the p.m. tube. A comparatively small amount of audio power is sufficient to trigger the p.m. tube into releasing its power into the common final tank circuit.

When receiving super-modulated signals on a conventional receiver equipped with a.v.c. the background noise will tend to rise during periods of reduced carrier. This action will cause no difficulty in the majority of cases unless the carrier suppression is severe. In any event, the turning off of the a.v.c. will result in a much more readable signal when this occurs. It is advisable to try both ways.

I have heard super-modulation referred to as a form of pulse modulation and unlawful for amateurs. Super is definitely amplitude modulation. The word "pulse" could just as readily describe the driving power to a pair of class "B" modulators. One works as much on a pulse basis as the other. Super has been referred to as a form of low-level grid modulation, perhaps as a result of a hasty glance at the schematic diagram. Because the modulation is added to the carrier in the final transmitter stage, this insures its being high level. Although audio is applied to the tube grids, the p.m. tube is not a class "C" amplifier making a constant carrier as would be found in grid modulation systems. The p.m. tube is actually an r.f. modulator and can be thought of as taking the place of the usual class "B" modulators used in regular-method AM transmitters. In conclusion, super-modulation represents real efficiency. The p.m. or modulator tube is dead until you speak. Then it releases r.f. power at an audio rate only half of the time, on the positive audio voltage alternations. On the negative alternations it is cooling. Expensive audio transformers are not required. It's still cheaper to obtain say 100 watts of r.f. power than the same amount of audio power.

 

* Taylor, R. E.: "The Taylor 'Super-Modulation' Principle," Radio & Television News, Sept. and Oct., 1948.

 

 

Posted June 12, 2020

Innovative Power Products Couplers

About RF Cafe

Kirt Blattenberger - RF Cafe Webmaster

Copyright: 1996 - 2024

Webmaster:

    Kirt Blattenberger,

    BSEE - KB3UON

RF Cafe began life in 1996 as "RF Tools" in an AOL screen name web space totaling 2 MB. Its primary purpose was to provide me with ready access to commonly needed formulas and reference material while performing my work as an RF system and circuit design engineer. The World Wide Web (Internet) was largely an unknown entity at the time and bandwidth was a scarce commodity. Dial-up modems blazed along at 14.4 kbps while tying up your telephone line, and a nice lady's voice announced "You've Got Mail" when a new message arrived...

Copyright  1996 - 2026

All trademarks, copyrights, patents, and other rights of ownership to images and text used on the RF Cafe website are hereby acknowledged.

All trademarks, copyrights, patents, and other rights of ownership to images and text used on the RF Cafe website are hereby acknowledged.

My Hobby Website:

AirplanesAndRockets.com

Copper Mountain Technologies (VNA) - RF Cafe

withwave microwave devices - RF Cafe

KR Electronics (RF Filters) - RF Cafe