Summary !!! WIP !!! This is an OpenRC Project for a Go-Kart As Some friends and I decided to create an extra class for hobby driver with self printed RC cars ... we started this project. We will try to reuse as much as possible from other projects so that it can be reused even here. (Less engineering and of course a higher reuse of components and knowledge) There will be also a driver in the nearer future which should be able to steer and move the head to where it drives. Feel free to comment...
Topics: fun, gokart, RC_Car, thingiverse, openrc, Competition, Go-Kart, racing, stl

Just a simple Go-Kart I designed myself. Thanks! Comment what you think, and happy printing!
Topics: racing, stl, Go-Kart, simple, Vehicles, kart, Go Kart, car, thingiverse, gokart

!!! WIP !!! This is an OpenRC Project for a Go-Kart As Some friends and I decided to create an extra class for hobby driver with self printed RC cars ... we started this project. We will try to reuse as much as possible from other projects so that it can be reused even here. (Less engineering and of course a higher reuse of components and knowledge) PartList: Screws: 4 x M3x16 lenshead 4 x M3x10 lenshead 10 x M3x12 countersunk 13 x M3x10 countersunk 30 x M3x8 countersunk Nuts 14 x M3 Bearings:...
Topics: racing, R/C Vehicles, Go-Kart, Fun, gokart, OpenRCproject, openrc, RC_Car, thingiverse,...

This is a 3" wide x 1.25" high x .25" thick gokart. You can hang it from your mirror, etc... Prints well without support. The pictures are of one I cut my friend's racing number into. If you would like one with a particular racing number cut into it, just leave me a comment with the number and I'll upload one with your number on it. There is also a file for an Outlaw style kart. It is 3" wide by 2 3/8" high by 3/8" thick. Thanks, OzzyEarley, for making the...
Topics: thingiverse, go_kart_racing, gokart, stl, racing, gokart_racing, Sport & Outdoors, go_kart, kart

This is an outlaw style gokart design with wings. It is 3" wide by 2 3/8" tall by 3/8" thick. It prints well without support. If you want a racing number cut out of the wing, let me know and I can upload one for you. Thanks, OzzyEarley, for the suggestion to make it.
Topics: thingiverse, gokart, stl, racing, Sport & Outdoors, go_kart, outlaw, kart

This is a twist throttle to replace a cheap Chinese one. I made this because the inner part was weak, short, and just bad. This is stronger and turns a lot better. I suggest you clean up the supports good, and lubricate the part where the cable goes in, so it turns and doesn't make noise. It is also good to drill out the hole because some cables have a bigger thing at the end. Thanks!
Topics: gokart, engine, twist, throttle, pitbike, small, Automotive, thingiverse, go kart, mini bike, pit...

These are replacement pedals for the Segway Ninebot Drift Kart. My son is 5 years old and he's just a little bit too short to use the normal pedals so we had been using cushions in the seat. These extend the pedals back so he can more easily use them. Designed to use the existing super short screws. I'll provide pictures of them installed once they're done printing. Supports are required underneath because there is a lip to hold the pedals in place.
Topics: thingiverse, ninebot, drift kart, extended, pedal, Automotive, gocart, gokart, segway, pedals, go...

This Go-Kart is Awesome! It has been smoothed and Remixed with no #s Use countersunk screws to attach the wheels and a long one for the steering wheel, you'll have to choose the size accordingly, depending on how big you want to print it and your scaling Happy Printing!
Topics: Vehicles, gokart, Kart, racing, thingiverse, car, race, go_kart, racer, stl

I made this for my go kart. The pedal is 1.5" W x 6.25" L . This has all the parts in the STL file I will be making the other pedals later for brake and clutch. you might have to scale it just a little in the slicing software. I slightly undersized the bolt holes which are 8mm bolts in diameter. scale to 102%.
Topics: AutoCAD, pedal, gas pedal, Automotive, gokart, stl, thingiverse