What's new in 6.48.5 (2021-Sep-21 13:50):

Changes since 6.48.4:

*) branding - properly clean up old branding files before installing a new one;
*) crs3xx - fixed default MAC address calculation on management Ethernet for CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) gps - improved interface monitoring;
*) health - improved temperature reporting;
*) ike2 - check if TS is still valid after obtaining SPI;
*) ipsec - improved SA update by SPI;
*) netinstall - require Netinstall version to be the same or newer as "factory-software";
*) poe - update PoE firmware only on devices that supports it;
*) ppp - improved stability when receiving bogus response on modem channel;
*) qsfp - improved system stability when setting unsupported link rates;
*) sfp - added "sfp-rate-select" setting (CLI only);
*) sfp - improved SFP, SFP+, SFP28 and QSFP+ interface stability for CRS3xx and CCR2004 devices;
*) sfp28 - changed FEC auto mode to disabled;
*) w60g - limit power output when using region EU to match EN302567 on nRAY;
*) w60g - use EU region by default;
*) winbox - added "name" and "file-name" parameter when importing and exporting certificates;
*) winbox - allow setting MCS (24-31) to 4x4 Wireless interfaces;
*) winbox - do not allow to set empty "init-string" field under "System/GPS" menu;
*) winbox - do not show "GPS antenna" selection for devices without selection support;
*) winbox - show "System/Health/Settings" only on boards that have configurable values;
*) winbox - show "current-channel" column by default for CAP interfaces;
*) wireless - added U-NII-2 support for US and Canada country profiles for hAP ac lite;

Changelog archive ×

What's new in 6.49rc2 (2021-Sep-28 10:17):

Changes in this release:

*) bridge - improved controller bridge stability when adding RouterOS v7 port extender;
*) bridge - improved port extender stability when creating bond interfaces on excluded ports;
*) crs3xx - fixed bridge controller and extender packet forwarding for CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) dhcp-server - fixed DHCP Option decimal value parsing;
*) discovery - do not send discovery packets on interfaces that are blocked by STP (introduced in v6.48);
*) sfp - added "sfp-rate-select" setting;
*) supout - added controller bridge section;
*) switch - fixed (R/M)STP port blocking right before switching them in HW bridge (fixes possible packet loop when changing bridge settings);
*) user - added "expired" user status with suggestion to change password (WinBox v3.29 required);
*) user - fixed active user session purging on disconnect;
*) user - show "expired password" prompt for users with blank password;
*) winbox - added "fec-mode" parameter under "Interface/Ethernet" menu;
*) winbox - minimal required version is v3.30;
*) wireless - improved system stability when sending packets through interface after L2MTU is increased;

Other changes since v6.48.4:

*) backup - fixed backup file restore (introduced in v6.49beta);
*) branding - fixed LCD logo loading from branding package when installed via Netinstall;
*) branding - properly clean up old branding files before installing a new one;
*) bridge - added IGMP and MLD querier monitoring;
*) bridge - added IGMP snooping log when multicast table gets full;
*) bridge - fixed external flag in the host table for wireless clients;
*) bridge - improved stability when quickly adding and removing bridge interface;
*) bridge - improved system stability when disabling IGMP/MLD querier port (introduced in v6.49beta22);
*) chr - fixed OS provisioning on Azure;
*) chr - improved stability when changing "flow-control" settings on interfaces with e1000 drivers;
*) conntrack - increased total connection tracking table size based on installed RAM size;
*) console - require "write+ftp" permissions for executing script to file;
*) console - require "write+ftp" permissions for printing to file;
*) crs3xx - correctly filter packets by L2MTU on 1Gbps Ethernet interfaces for CRS354 devices;
*) crs3xx - fixed LEDs for QSFP+ interface on CRS326-24S+2Q+ device;
*) crs3xx - fixed SFP and SFP+ link rate reporting (introduced in v6.48beta11);
*) crs3xx - fixed default MAC address calculation on management Ethernet for CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - fixed interface flow control;
*) crs3xx - fixed jumbo frame forwarding for CRS354 devices (introduced in v6.49beta36);
*) crs3xx - fixed packet forwarding on 1Gbps Ethernet interfaces for CRS354 devices (introduced in v6.49beta44);
*) crs3xx - improved QSFP+ linking and mode changing for CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - improved packet transmit on SFP+ interfaces;
*) crs3xx - improved switch resource allocation for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - improved system stability when learning MDB and FBD entries for CRS312, CRS326-24S+2Q+ and CRS354 devices (introduced in v6.49beta44);
*) defconf - apply default configuration from branding package when performing reset with button;
*) defconf - removed overlapping IPv6 firewall rules;
*) defconf - use router as DNS server for DHCP hosts;
*) dhcpv4-server - reset lease's dynamic "bcast" flag on packets from relay;
*) dhcpv6-server - check if pool name has changed from RADIUS on renew;
*) dhcpv6-server - improved dynamic server entry update;
*) firewall - fixed "ingress-priority" matcher;
*) firewall - fixed GRE protocol packets considered invalid when PPTP helper is disabled;
*) gps - improved interface monitoring;
*) health - added "phy-temperature" sensor monitoring for CRS312 device;
*) health - improved temperature reporting;
*) ike2 - added support for ASN.1 DN "my-id" value setting for initiators;
*) ike2 - check if TS is still valid after obtaining SPI;
*) ike2 - fixed initiator packet retransmit with DDOS cookie;
*) ipsec - improved SA update by SPI;
*) ipsec - improved system stability on CHR;
*) ipsec - improved system stability on MMIPS devices;
*) kid-control - improved IPv6 firewall rule generation;
*) leds - fixed LTE LED default mapping for wAP R ac LTE kit;
*) lora - added additional predefined network servers;
*) lora - added channel plan "il-917" for Israel;
*) lora - fixed "PULL_DATA" token generation;
*) m33g - improved support for "/system gpio" menu ("/system routerboard upgrade" required);
*) m33g - removed 12..16 pins from "/system gpio" menu;
*) mipsbe - improved booting speed on non-NAND devices ("/system routerboard upgrade" required);
*) mpls - allow to disable FastPath (CLI only);
*) mqtt - added server name indication;
*) netinstall - fixed lock file persistence after reinstall;
*) netinstall - improved bootp packet handling on Linux netinstall-cli version when multiple NIC's are present;
*) netinstall - require Netinstall version to be the same or newer as "factory-software";
*) ntp - use correct IPv6 multicast group for SNTP client;
*) package - always allow to uninstall package even if there is no free disk space left;
*) poe - fixed PoE out functionality on CRS354 (introduced in v6.49beta22);
*) poe - update PoE firmware only on devices that supports it;
*) ppp - improved stability when receiving bogus response on modem channel;
*) qsfp - improved system stability when setting unsupported link rates;
*) rb922 - fixed miniPCI-e card detection (introduced in v6.49beta11);
*) routerboard - fixed "reformat-hold-button-max" validation for values below 10s;
*) sfp - added "sfp-rate-select" setting (CLI only);
*) sfp - fixed GPON module linking (introduced in v6.47);
*) sfp - improved 25Gbps optical module stability and linking;
*) sfp - improved SFP, SFP+, SFP28 and QSFP+ interface stability for CRS3xx and CCR2004 devices;
*) sfp - improved link stability for 10G, 25G and 40G modules on CRS309, CRS312, CRS326-24S+2Q+ CRS354 and CCR2004 devices;
*) sfp28 - changed FEC auto mode to disabled;
*) snmp - added "engine-id" OID support;
*) snmp - fixed "ipNetToMediaType" OID for incomplete entries;
*) ssh - fixed "undo" functionality;
*) supout - print detailed list of active user sessions;
*) switch - fixed (R/M)STP port blocking right before switching them in HW bridge (fixes possible packet loop when changing bridge settings);
*) switch - improved packet transmit between CPU and 98PX1012 for CCR2004-1G-12S+2XS device;
*) swos - fixed "static-ip-address" parameter;
*) tr069-client - added "X_MIKROTIK_LinkDowns" parameter for interface "link-downs" value reporting;
*) tr069-client - added support for Ethernet link speed reporting;
*) tr069-client - added support for interface comment reporting and editing;
*) tr069-client - added support for supout file upload;
*) tr069-client - fixed traceroute diagnostics time values;
*) tr069-client - improved XML with new-lines for readable output;
*) tr069-client - improved stability for download/upload diagnostics;
*) upgrade - fixed free space checking on flash type memories when installing new packages;
*) ups - added battery info for APC Back-UPS BX750MI;
*) w60g - general stability and performance improvements;
*) w60g - limit power output when using region EU to match EN302567 on nRAY;
*) w60g - use EU region by default;
*) webfig - added support for logo image from branding package;
*) webfig - do not show value units twice;
*) webfig - fixed "Wireless/CAP" menu opening;
*) webfig - fixed interface sorting by name;
*) webfig - show only "Close" button under "Wireless/Wireless Sniffer/Sniffed Packets" menu;
*) winbox - added "dhcp" option to "multicast-helper" setting;
*) winbox - added "interface-speed-100G" LED type to "System/LEDs" menu;
*) winbox - added "name" and "file-name" parameter when importing and exporting certificates;
*) winbox - added "sfp-shutdown-temperature" setting to SFP interfaces;
*) winbox - added SSH settings under "IP/SSH" menu;
*) winbox - added TFTP settings under "IP/TFTP/Settings" menu;
*) winbox - allow setting MCS (24-31) to 4x4 Wireless interfaces;
*) winbox - do not allow to add/remove W60G interfaces;
*) winbox - do not allow to set empty "init-string" field under "System/GPS" menu;
*) winbox - do not show "GPS antenna" selection for devices without selection support;
*) winbox - fixed "Secondary Frequency" parameter setting under "CAPsMAN/Channel" menu;
*) winbox - fixed DNS "cache-size" parameter setting;
*) winbox - fixed health reporting on RB960, hEX, hEX S and hAP ac3 devices;
*) winbox - fixed order of weekdays under "IP/Firewall" menu;
*) winbox - fixed support for "Delegated-IPv6-Prefix" for PPP services;
*) winbox - match "MAC Protocol-Num" predefined values under "Bridge/Filters" menu;
*) winbox - properly show "CRL Signature" field under "System/Certificate" menu;
*) winbox - separated CCQ Tx and Rx values in their own unique columns;
*) winbox - show "System/Health/Settings" only on boards that have configurable values;
*) winbox - show "current-channel" column by default for CAP interfaces;
*) winbox - show IPv6 address in separate field under "IP/Cloud" menu;
*) wireless - added U-NII-2 support for US and Canada country profiles for hAP ac lite;
*) wireless - added override for multicast-to-unicast translation of DHCP traffic;
*) wireless - do not remove channels >2462 MHz from "scanlist" if scanning for fixed channel;
*) wireless - do not send packet back to station-bridge it was received from;
*) wireless - fixed minor typo in debug logging messages;
*) wireless - improve WMM priority assignment for packets with internal priority greater than 7;
*) wireless - improve regulatory compliance with DFS requirements;
*) wireless - improve signaling of QCA9984 interface capabilities when using 160/80+80MHz channel width;
*) wireless - improved system stability on several 802.11ac devices (introduced in v6.49beta36);
*) wireless - log client signal strength on disconnect;
*) wireless - renamed "secondary-channel" to "secondary-frequency";
*) wireless - updated "israel" regulatory domain information;
*) wireless - updated "united kingdom" regulatory domain information;

Changelog archive ×

What's new in 6.49 (2021-Oct-06 11:55):

*) branding - fixed LCD logo loading from branding package when installed via Netinstall;
*) branding - properly clean up old branding files before installing a new one;
*) bridge - added IGMP and MLD querier monitoring;
*) bridge - added IGMP snooping log when multicast table gets full;
*) bridge - fixed external flag in the host table for wireless clients;
*) bridge - improved controller bridge stability when adding RouterOS v7 port extender;
*) bridge - improved port extender stability when creating bond interfaces on excluded ports;
*) bridge - improved stability when quickly adding and removing bridge interface;
*) certificate - improved stability when removing dynamic CRL entries;
*) chr - fixed OS provisioning on Azure;
*) chr - improved stability when changing "flow-control" settings on interfaces with e1000 drivers;
*) conntrack - increased total connection tracking table size based on installed RAM size;
*) console - require "write+ftp" permissions for executing script to file;
*) console - require "write+ftp" permissions for printing to file;
*) crs3xx - correctly filter packets by L2MTU on 1Gbps Ethernet interfaces for CRS354 devices;
*) crs3xx - fixed LEDs for QSFP+ interface on CRS326-24S+2Q+ device;
*) crs3xx - fixed SFP and SFP+ link rate reporting (introduced in v6.48beta11);
*) crs3xx - fixed bridge controller and extender packet forwarding for CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - fixed default MAC address calculation on management Ethernet for CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - fixed interface flow control;
*) crs3xx - improved QSFP+ linking and mode changing for CRS326-24S+2Q+ and CRS354 devices;
*) crs3xx - improved packet transmit on SFP+ interfaces;
*) crs3xx - improved switch resource allocation for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
*) defconf - apply default configuration from branding package when performing reset with button;
*) defconf - removed overlapping IPv6 firewall rules;
*) defconf - use router as DNS server for DHCP hosts;
*) dhcp-server - fixed DHCP Option decimal value parsing;
*) dhcpv4-server - reset dynamic "bcast" flag when receiving offer from DHCP relay;
*) dhcpv4-server - reset lease's dynamic "bcast" flag on packets from relay;
*) dhcpv6-server - check if pool name has changed from RADIUS on renew;
*) dhcpv6-server - improved dynamic server entry update;
*) discovery - do not send discovery packets on interfaces that are blocked by STP (introduced in v6.48);
*) dns - fixed memory leak caused by large DNS replies;
*) firewall - fixed "ingress-priority" matcher;
*) firewall - fixed GRE protocol packets considered invalid when PPTP helper is disabled;
*) gps - improved interface monitoring;
*) health - added "phy-temperature" sensor monitoring for CRS312 device;
*) health - improved temperature readings on hEX S;
*) health - improved temperature reporting;
*) ike2 - added support for ASN.1 DN "my-id" value setting for initiators;
*) ike2 - check if TS is still valid after obtaining SPI;
*) ike2 - fixed initiator packet retransmit with DDOS cookie;
*) ipsec - fixed memory leak when processing DHCP packets;
*) ipsec - improved SA update by SPI;
*) ipsec - improved system stability on CHR;
*) ipsec - improved system stability on MMIPS devices;
*) kid-control - improved IPv6 firewall rule generation;
*) led - added LTE LED support for LHGGR;
*) leds - fixed LTE LED default mapping for wAP R ac LTE kit;
*) lora - added additional predefined network servers;
*) lora - added channel plan "il-917" for Israel;
*) lora - fixed "PULL_DATA" token generation;
*) m33g - improved support for "/system gpio" menu ("/system routerboard upgrade" required);
*) m33g - removed 12..16 pins from "/system gpio" menu;
*) mipsbe - improved booting speed on non-NAND devices ("/system routerboard upgrade" required);
*) mpls - allow to disable FastPath (CLI only);
*) mqtt - added server name indication;
*) netinstall - fixed lock file persistence after reinstall;
*) netinstall - improved bootp packet handling on Linux netinstall-cli version when multiple NIC's are present;
*) netinstall - require Netinstall version to be the same or newer as "factory-software";
*) ntp - use correct IPv6 multicast group for SNTP client;
*) package - always allow to uninstall package even if there is no free disk space left;
*) poe - update PoE firmware only on devices that supports it;
*) ppp - improved stability when receiving bogus response on modem channel;
*) qsfp - improved system stability when setting unsupported link rates;
*) quickset - use 5GHz interface's country for "Home AP Dual" configuration;
*) routerboard - fixed "reformat-hold-button-max" validation for values below 10s;
*) sfp - added "sfp-rate-select" setting;
*) sfp - fixed GPON module linking (introduced in v6.47);
*) sfp - improved 25Gbps optical module stability and linking;
*) sfp - improved SFP, SFP+, SFP28 and QSFP+ interface stability for CRS3xx and CCR2004 devices;
*) sfp - improved link stability for 10G, 25G and 40G modules on CRS309, CRS312, CRS326-24S+2Q+ CRS354 and CCR2004 devices;
*) sfp28 - changed FEC auto mode to disabled;
*) snmp - added "engine-id" OID support;
*) snmp - fixed "ipNetToMediaType" OID for incomplete entries;
*) ssh - fixed "undo" functionality;
*) supout - added controller bridge section;
*) supout - print detailed list of active user sessions;
*) switch - fixed (R/M)STP port blocking right before switching them in HW bridge (fixes possible packet loop when changing bridge settings);
*) switch - improved packet transmit between CPU and 98PX1012 for CCR2004-1G-12S+2XS device;
*) swos - fixed "static-ip-address" parameter;
*) tr069-client - added "X_MIKROTIK_LinkDowns" parameter for interface "link-downs" value reporting;
*) tr069-client - added support for Ethernet link speed reporting;
*) tr069-client - added support for interface comment reporting and editing;
*) tr069-client - added support for supout file upload;
*) tr069-client - fixed traceroute diagnostics time values;
*) tr069-client - improved XML with new-lines for readable output;
*) tr069-client - improved stability for download/upload diagnostics;
*) upgrade - fixed free space checking on flash type memories when installing new packages;
*) ups - added battery info for APC Back-UPS BX750MI;
*) user - added "expired" user status with suggestion to change password (WinBox v3.29 required);
*) user - fixed active user session purging on disconnect;
*) user - show "expired password" prompt for users with blank password;
*) w60g - general stability and performance improvements;
*) w60g - limit power output when using region EU to match EN302567 on nRAY;
*) w60g - use EU region by default;
*) webfig - added support for logo image from branding package;
*) webfig - do not show value units twice;
*) webfig - fixed "Wireless/CAP" menu opening;
*) webfig - fixed interface sorting by name;
*) webfig - show only "Close" button under "Wireless/Wireless Sniffer/Sniffed Packets" menu;
*) winbox - added "dhcp" option to "multicast-helper" setting;
*) winbox - added "fec-mode" parameter under "Interface/Ethernet" menu;
*) winbox - added "interface-speed-100G" LED type to "System/LEDs" menu;
*) winbox - added "name" and "file-name" parameter when importing and exporting certificates;
*) winbox - added "sfp-shutdown-temperature" setting to SFP interfaces;
*) winbox - added SSH settings under "IP/SSH" menu;
*) winbox - added TFTP settings under "IP/TFTP/Settings" menu;
*) winbox - allow setting MCS (24-31) to 4x4 Wireless interfaces;
*) winbox - do not allow to add/remove W60G interfaces;
*) winbox - do not allow to set empty "init-string" field under "System/GPS" menu;
*) winbox - do not show "GPS antenna" selection for devices without selection support;
*) winbox - fixed "Secondary Frequency" parameter setting under "CAPsMAN/Channel" menu;
*) winbox - fixed DNS "cache-size" parameter setting;
*) winbox - fixed health reporting on RB960, hEX, hEX S and hAP ac3 devices;
*) winbox - fixed order of weekdays under "IP/Firewall" menu;
*) winbox - fixed support for "Delegated-IPv6-Prefix" for PPP services;
*) winbox - match "MAC Protocol-Num" predefined values under "Bridge/Filters" menu;
*) winbox - minimal required version is v3.30;
*) winbox - properly show "CRL Signature" field under "System/Certificate" menu;
*) winbox - separated CCQ Tx and Rx values in their own unique columns;
*) winbox - show "System/Health/Settings" only on boards that have configurable values;
*) winbox - show "current-channel" column by default for CAP interfaces;
*) winbox - show IPv6 address in separate field under "IP/Cloud" menu;
*) wireless - added U-NII-2 support for US and Canada country profiles for hAP ac lite;
*) wireless - added override for multicast-to-unicast translation of DHCP traffic;
*) wireless - do not remove channels >2462 MHz from "scanlist" if scanning for fixed channel;
*) wireless - do not send packet back to station-bridge it was received from;
*) wireless - fixed minor typo in debug logging messages;
*) wireless - improve WMM priority assignment for packets with internal priority greater than 7;
*) wireless - improve regulatory compliance with DFS requirements;
*) wireless - improve signaling of QCA9984 interface capabilities when using 160/80+80MHz channel width;
*) wireless - improved system stability when sending packets through interface after L2MTU is increased;
*) wireless - log client signal strength on disconnect;
*) wireless - renamed "secondary-channel" to "secondary-frequency";
*) wireless - updated "israel" regulatory domain information;
*) wireless - updated "united kingdom" regulatory domain information;

Changelog archive ×

What's new in 7.1rc5 (2021-Oct-25 20:15):

!) container - package is getting updated and will be made available in future, if interested in container feature please use 7.1rc4;
*) arm64 - fixed "total-sector-writes" resetting on each startup;
*) bgp - fixed IBGP nexthop selection;
*) bgp - fixed binding to IPv6 "link-local" address;
*) bgp - fixed missing default "local-pref" on selection;
*) bgp - fixed stability when appending extended communities;
*) bgp - improved stability and other minor fixes;
*) bonding - added warning when using 802.3ad mode without MII link monitoring;
*) bridge - added HW offload support for vlan-filtering on MT7621 switch chip (hEX, hEX S, RBM33G, RBM11G, LtAP);
*) bridge - fixed incorrect "hw=no" setting after reboot in rare cases;
*) bridge - improved MLAG stability;
*) capsman - do not include "access-list" passphrases in the output of export command by default;
*) certificate - added ability to choose the digest algorithm when generating a certificate;
*) chr - fixed FastPath support for VMXNET3 drivers;
*) dhcpv4 - fixed backslash prefix for packet logging;
*) dhcpv6-client - show correct DUID in print;
*) dhcpv6-server - fixed "address-pool" default value;
*) dhcpv6-server - fixed DUID generation with timestamp;
*) dns - fixed memory leak caused by large DNS replies;
*) gps - fixed built-in GPS functionality for LtAP;
*) health - fixed health value reporting on RB5009;
*) ipsec - enabled hardware acceleration support for ARM and ARM64 devices;
*) ipsec - fixed hardware acceleration support for CHR;
*) l3hw - fixed MTU on receive;
*) l3hw - fixed source MAC address usage for routed packets;
*) leds - adjust "system-led" color based on cellular connection technology on Chateau devices;
*) leds - fixed LED configuration on RB4011;
*) ltap - improved PCIe card support;
*) lte - added "at-chat" support in MBIM mode for Simcom modems in USB composition mode 9003;
*) lte - improved APN re-connection on non LTE networks;
*) lte - improved modem signal monitoring on Chateau 5G;
*) lte - moved notifications about incorrect responses from modem to 'lte' topic;
*) lte - properly show antenna selection on Chateau devices;
*) lte - request modem to restart registration process if timeout detected;
*) ospf - accept LA prefixes from intra-area router's LSA to the routing table;
*) mpls - added ICMP handler (send ICMP ttl exceed on MPLS ttl expiry);
*) ospf - allow to set IPv6 networks for "interface-template";
*) ospf - disable areas with no interface configuration;
*) ospf - do not allow to set "ptp-unnumbered" on IPv6 interfaces;
*) ospf - do not set empty filter chains when upgrading from v6;
*) ospf - improved stability and other minor fixes;
*) ospf - show interface's hello, re-transmit and dead intervals;
*) package - uninstall "container" package when downgrading to v6;
*) pppoe - fixed DHCPv6 PD;
*) quickset - added 5G signal quality information;
*) quickset - made "Password..." button work in Basic AP mode;
*) route - improved stability and other minor fixes;
*) route-filters - fixed "<=" and ">=";
*) route-filters - fixed "ext-community" problems;
*) route-filters - fixed "num range" matchers;
*) route-filters - fixed "route origin" matcher;
*) route-filters - improved completion;
*) route-filters - improved stability and other minor fixes;
*) rpki - added "rpki-query" command;
*) rpki - other minor fixes;
*) snmp - fixed IPsec-SA stats counter reporting;
*) snmp - fixed bulk get/walk with large neighbor version strings;
*) ssl - added support for additional GCM_SHA384 ciphers;
*) ssl - fixed x509 chain validation;
*) switch - fixed bogus statistics after RTL8367 switch reset;
*) system - improved DHCP and HotSpot service stability when shutting down;
*) system - improved system stability when downgrading to v6 with external disks attached;
*) tr069-client - improved compatibility for 5G;
*) traffic-flow - added systematic count-based packet sampling support;
*) user-manager - fixed "rate-limit-priority" parameter;
*) user-manager - fixed PEAP server authentication for Windows clients;
*) vrf - allow to assign interfaces directly along with interface lists;
*) vxlan - added default L2MTU value for improved connectivity in bridged setups;
*) vxlan - improved speed on MIPSBE devices;
*) wifiwave2 - fixed configuration profile renaming;
*) wifiwave2 - moved RADIUS accounting parameters to a separate configuration profile;
*) winbox - added "netmap" action to IPv6 NAT rules;
*) winbox - added IPv6 support for "Network" parameter under "Routing/OSFP/Interface Templates" menu;
*) winbox - added missing IPv6 mangle actions - "mark-routing", "sniff-tzsp", "sniff-pc", "snpt" and "dnpt";
*) winbox - added option to upgrade LTE firmware;
*) winbox - changed extension channel symbol to lower case for WifiWave2;
*) winbox - do not allow to set "memory-lines" parameter out of bounds under "System/Logging/Action" menu;
*) winbox - fixed "routing-mark" and "routing-table" selection in IPv4 and IPv6 firewall and route rules;
*) winbox - fixed private SSH key import;
*) winbox - made "0" the default value for GPS "init-channel" parameter;
*) winbox - made SSID field collapsible for WifiWave2;
*) winbox - moved "RPKI" tab from "Routing/BGP" to "Routing/RPKI" menu;
*) winbox - moved "Tables" tab from "IP/Route" to "Routing" menu;
*) winbox - moved all interface stats columns to the right;
*) winbox - properly load all backups stored in Cloud;
*) winbox - properly show "value" parameter for FWD type entries;
*) winbox - renamed "Backlight" to "OK" under "LCD/Backlight" menu;
*) winbox - renamed "Dst. Address" to "Route Dst." under "IP/Firewall/Mangle" menu;
*) winbox - replaced "routing-table" with VRF in traceroute;
*) winbox - show "External Antenna" parameter on all Chateau devices;
*) winbox - updated WifiWave2 interface fields and tabs;
*) wireguard - do not consider WireGuard interface as ethernet;
*) wireguard - improved system stability when sending WireGuard packets over EoIP;
*) wireless - adjusted antenna gain on Chateau devices;
*) wireless - improved system stability when changing L2MTU for wireless interfaces;
*) wireless - improved system stability when limiting link throughput via "ap-tx-limit" and "client-tx-limit" parameters;
*) wireless - improved system stability when using nv2 protocol on ipq4019 interfaces;

Changelog archive ×