[DEPRECATED] ASRock Rack EP2C602 Install Guide for Sierra and High Sierra

[JustinKay]

Ah! Thank you SO much for your patience, I'm def a noob at this

Removed "SSDT-UIAC" file and put a stock USBInjectAll.kext in my kexts>other folder

Two Questions:
1.Under config file, ACPI>DSDT, sHould I disable "Rename EUSB to EH01" and "Rename USBE to EH02"? I tried disabling and still get the same error

2. Would step 1 in the OP of renaming "LAN NIC" still be the same if I have a different board? I did that using Kubuntu

 

[teamawesome]

Ah! Thank you SO much for your patience, I'm def a noob at this

Removed "SSDT-UIAC" file and put a stock USBInjectAll.kext in my kexts>other folder

Two Questions:
1.Under config file, ACPI>DSDT, sHould I disable "Rename EUSB to EH01" and "Rename USBE to EH02"? I tried disabling and still get the same error

2. Would step 1 in the OP of renaming "LAN NIC" still be the same if I have a different board?

Your board has 4 x Intel 82574L NIC's. The EP2C602 has only 2 NIC's of the same type. The process of flashing them will be similar but different. DO NOT follow the instructions blindly and just start flashing. However, you can use ethtool to determine the four NIC names to be changed for your board.

Did you read through the Rehabman guide for using USBInjectAll? That will walk you through everything in detail regarding that kexts and its related injector SSDT.

 

[JustinKay]

Yes when I booted into linux, ran ethtools, found out the 4 NIC's and then used these commands:
ethtool -E ????? magic 0x10D38086 offset 0x16 value 0x00
ethtool -E ????? magic 0x10D38086 offset 0x17 value 0x00
ethtool -E ????? magic 0x10D38086 offset 0x1A value 0xF6
ethtool -E ????? magic 0x10D38086 offset 0x16 value 0x00
(With "?????" as NIC)

As for Rehabman guide, I assumed I just put kext file in "other" folder then will be able to boot into system, run ioregistry.app to then create SSDT. Is that not right?

 

[teamawesome]

Yes when I booted into linux, ran ethtools, found out the 4 NIC's and then used these commands:
ethtool -E ????? magic 0x10D38086 offset 0x16 value 0x00
ethtool -E ????? magic 0x10D38086 offset 0x17 value 0x00
ethtool -E ????? magic 0x10D38086 offset 0x1A value 0xF6
ethtool -E ????? magic 0x10D38086 offset 0x16 value 0x00
(With "?????" as NIC)

As for Rehabman guide, I assumed I just put kext file in "other" folder then will be able to boot into system, run ioregistry.app to then create SSDT. Is that not right?

I am going off memory here (which is always dangerous), but yes that sounds correct.

 

[JustinKay]

I am going off memory here (which is always dangerous), but yes that sounds correct.

Okay, I'm still not able to boot... I'll try a fresh install and see how far I get, thanks for your help!

 

[teamawesome]

Did you follow the full BIOS Guide for settings? I know it will deviate slightly.

 

[JustinKay]

Did you follow the full BIOS Guide for settings? I know it will deviate slightly.

Yeah, followed it, it was basically the same

 

[teamawesome]

If you post your EFI, I will look at it.

 

[JustinKay]

I can't thank you enough!

 

[teamawesome]

Overwrite the whole CLOVER directory with the attached folder and test.