Share this project

Done
Share
Embed

Share this project

Done
Email
Screw drivers wire striper knife electrical cable cutter fingernail clipper shackle wrench bottle opener lever key ring accessory

Metperial Titanium Little Bit More

Screw drivers wire striper knife electrical cable cutter fingernail clipper shackle wrench bottle opener lever key ring accessory
Created by
Ice, Myark, Casper and Denis Stewart
Ice, Myark, Casper and Denis Stewart
1,174 backers pledged AU$ 45,274 to help bring this project to life.
Rewards Campaign Updates 23 Comments 388 Community
Share this project

Refunds

Hi All

Refunds are offered when I have completed the 2200 Little Bit Mores,  I will personally purchase for my own stock, and if any loyal backer wants their reward its ok but... Read more

11 Comments 6 likes

Mean time I am on strike

Sorry all about the confusion

In the comments and messages I can not answer backers as kick starter staff   have cut all my projects communications and I can only communicate in updates.... Read more

15 Comments 6 likes

Hi Kick starter administration 

Hi Kick starter  administration 

I am going to suspend the Little Bit More project because of the troll you have supported with out a fair trial on my behalf, and... Read more

18 Comments 1 like

Little Bit More upate

Hi All

I have started a new project https://www.kickstarter.com/projects/363092515/gr5-titanium-little-pinch-more-multi-tool-keyring?ref=creator_nav   like I mentioned that fortunately Kick starter with their good heart and understanding excepted after explaining my position that's needed to compete this project.... Read more

29 Comments 2 likes

Little Bit Late update

Hi all

It’s hard for me to write this update as so much to explain with limited resourses to carry out the task at hand, most will know all the parts are made that... Read more

13 Comments 3 likes

I apologize for the delay in update

Hi all

I am sorry for the delay as I am in the final stage to assemble but still need to drill the holes for the titanium pin in the... Read more

21 Comments 14 likes

What I have decided to do

Hi all

I have encounter some teething problems with the Little Bit More such as to make the blade fit perfectly and to lock in place when shut that needs... Read more

15 Comments 10 likes

Laser welding Gr5 Titanium pin

Hi all

Pictured below is Tan with a test run with the jig he made today to surface grind the angle on end of blade of the Little Bit More... Read more

7 Comments 12 likes

Little Bit More update on CNC, EDM and drilling manufcature procdures.

Hi all

The picture below is surface grinding the Little Bit Mores as when in plate form before EDM wire cut, the titanium plates are slightly different thickness in size and needs to be ground... Read more

4 Comments 16 likes

Showing Little Bit Mores CNC machined

Hi all

The Little Bit More have started to be CNC machined which I have changed the style of CNC machinery to very small but more accurate and quicker CNC machines.... Read more

9 Comments 16 likes

2200 Little Bit More parts take time to EDM wire cut,

Hi all 

As explained in the last update the EDM workshop has shifted to a new area pictured below and by doing so had to before shifting workshops, finish mold tooling for a... Read more

3 Comments 13 likes

Little Bit More progress

Hi All

The picture shows the blade part cut from the 2.5mm gr 5 titanium plates which are stacked 16 plates high, then EDM wire cut.

Because each plate slightly... Read more

8 Comments 12 likes

Titanium arrived ready to start EDM wire cutting

Hi all

Picture attached below shows the rest of the Gr5 titanium plate that arrived yesterday and ready to EDM wire cut the Little Bit More manufacturing, after this update... Read more

2 Comments 7 likes

Little Bit More update

Hi all

The 2.5mm GR5 titanium sheet has just arrived that is cut into 32 pieces to suit the EDM wire cutter.

We did try to stamp the titanium sheet... Read more

17 likes

Little Bit More Update

Hi all

The Gr5 titanium sheet is ordered and cut to size before delivered that is to suit the EDM wire cutter also for cold forging the blade part which... Read more

5 Comments 10 likes

Send engraving needs to Little Bit More messages

Hi all

I have just had a message from several backers that there is no place to write the engraving needs on the survey I just sent,

Can you  please send... Read more

56 Comments 9 likes

Free Engraving offered for the Little Bit More

Hi all

 I am offering free engraving if any one may want their name etc . engraved on the Little Bit More as the cost is not much although it takes my... Read more

11 Comments 16 likes

Kicks Starter backer funds will be released early next week

Hi all

The Kicks Starter backer funds will be released early next week and is when I will send you the survey for your mailing addresses etc. I will also... Read more

3 likes

Thank you all 1174 times

Thank you all for the support and a great result with almost no marketing on my behalf because I am busy organizing the earlier kick starter project “Metperial Multi tool”... Read more

3 Comments 11 likes
Successfully raised AU$ 45,274 with 1,174 backers

I had a request

Hi all

I had a request from Akira Yuasa who is a faithful and generous backer, including my past kick starter projects, Akira asked if  I would be able to... Read more

3 Comments 9 likes

Thank you 1000 times

Hi all

Thank you for the trust and support given by almost 1000 backers of the Metperial Titanium Little Bit More.

The Little Bit More is a simple idea that... Read more

6 likes

$5000 stretch goal is reached in a day and a half

Wow the $5000 stretch goal is reached in a day and a half that means each Little Bit More is now supplied with a 24mm titanium split key ring as... Read more

3 likes

The $1000 goal is met in four hours

The $1000 goal is met in four hours after launching the Little Bit More project, WOW thank you all ever so much as I am lost for words right now... Read more
Project launched