CRT Monitors and Machines Repair Information

[a24tanabe]

Hello,everyone.

I want to repair X68000s and CRT monitors(ex.CZ-600D).
I could get some information about X68000s in this site(Many thanks!),so I could repair 2 X68000s.
But I can get CRT repair information.

Could you please tell me the site where I can get service manual about X68000s and their CRT monitors?
I could get CZ-300C in this site, and I want to get more information especially about CRT monitors.

I know repairing CRT monitors myself is very dangerous.But I must do it.
I called SHARP customer service and asked about repair and service manual,but I was refused.

Any information are welcome! Please help me.

Thanks.

 

[kamiboy]

I hope your Japanese is pretty good, or you are out of luck what service manuals are concerned.

Edit:

Sorry Tanabe-san, didnt realise that you are actually a Japanese member. As I am sure you know you will have much better luck finding repair information on the monitors on Japanese websites.

As for repairing CRT monitors, replacing the capacitors is a good place to start.

[a24tanabe]

Thank you for replying ,Mr.kamiboy.
I'm not good at English ,so I'm not sure that I tell you in correct nuance.

I wonder that some people get service manuals in what way.
Sharp said service manuals are not open,so they can not distribute them to general users.
But I know that some people get them from service person probably in unofficial ways.

I get X68030 Compact's service manual from this site.
So I want to know how to get other manuals about X68000s and monitors.

I think that to repair monitors, I should replace all capacitor at first, too.
But I know my friend tried to that(about 100 capacitors!) ,but it didn't work.
About repairing X68000s, I think it is necessary to replace all capacitors about PSU.
But about other digital circuit,I'm not sure that is necessary.
Of cource it is desirable, but other risks (such as immature soldering trouble) is worried.
In PSU board, it is one side patterned board, but other boards are layered having thru-holes.
I'm not sure I can solder in proper ways.

My moniter shows horizontal center line. I think that vertical control circuit is broken.
But I don't know where in the moniter ,there is vertical control circuit.
It is not particular problem about CZ monitors, so general information about CRT is welcome.

Not just in japan,CRT and CRT's information is fading away.
I want to get repair manuals about CRT,but I can get only one book, and it was too old to apply recent CRT.
I need CRT repair information not just about CZ-600D.

Sorry for long note and funniest English.
All information is welcome.

Thanks.

[BlueBMW]

The 68030 manual came in an unusual lot off yahoo.jp  The seller had mentioned something about how it shouldnt be distributed... oops. 

I dont know if there is any information on the sharp monitors in the inside/outside x68000 books or not.

[caius]

 

My moniter shows horizontal center line. I think that vertical control circuit is broken.
But I don't know where in the moniter ,there is vertical control circuit.
It is not particular problem about CZ monitors, so general information about CRT is welcome.

 

 

Yes right, first check the transistor of the vertical control (probably it's gone bad, if you don't know where it's located , google every transistor and see if they have this function), resolder  the flyback transformer and  CRT PCB solder points and check also ESR of the electrolytic capacitors.Let us know.

[kamiboy]

You might want to contact lukemorse1 on youtube.

http://www.youtube.com/user/lukemorse1

He lives in Japan, has experience with repairing X68000 monitors and he speaks Japanese.

He is also really nice.

[SuperDeadite]

You might want to contact lukemorse1 on youtube.

http://www.youtube.com/user/lukemorse1

He lives in Japan, has experience with repairing X68000 monitors and he speaks Japanese.

He is also really nice.

I would seriously NOT recommend going to lukemorse1 for X68K tech questions.  This is the guy that sold people X68K computers with old Macintosh video adapters.........

[kamiboy]

Everyone makes mistakes, that is how we learn. I've seen him repair X68000 monitors on his channel, so he knows somethings. And if nothing else he might know about better sources of information.

[caius]

Judging on how he desolders an SMD TSOP 62256 RAM:

Recent Repairs, On The Camera MVS Repairs And Thanks To mjs256 For The Ram Chips

I'd start to have some doubts on this guy...

[kamiboy]

Hey man, that chip is dead, so I dont see any problem with that particular technique. Actually it is a pretty smart way of getting rid of an SMD if you do not have a heat gun, or are not partial to their use.

Whatvis with the lukemorse hate on the net among modders? He gets the job done.

[BlueBMW]

My only experience with a luke morse machine was an x68000 expert with a horrible hack job atx swap.  It was a fire and dafety hazard all in one.  But otherwise, whatever